Learn

2)Design Loads & Load Combinations

Design Loads & Load Combinations

Lecture 2

Concrete Technology

Specification & Codes

These are rules given by various organizations in order to guide the designers for safe and economical design of structures

Various Codes of Practices are

  • ACI 318 By American Concrete Institute. For general

    concrete constructions (buildings)

  • AASHTO Specifications for Concrete Bridges. By American Association of State Highway and Transportation Officials.
  • ASTM (American Standards for Testing and Materials) for testing of materials.
  • ASCE 7 (American Society of Civil Engineers) for loads and design criteria for buildings

    Design Loads/ Load Patterns

    Dead Load

    “The loads which do not change their magnitude and position w.r.t. time within the life of structure”

    Dead load mainly consist of superimposed loads and self load of structure.

    • Self Load

      It is the load of structural member due to its own weight.

    • Superimposed Load

    It is the load supported by a structural member. For instance self weight of column is self load and load of beam and slab over it is superimposed load.

    • • • 

    •••

    •• 

    •• •• 


    • • 

    Spandirel  

    beam

    Column

    0· 1s t slab

    • • • 

    .L…-….-

    -am ·

    Slab on grade7

    Live Load

    Design Loads

    “Live loads consist chiefly of occupancy loads in buildings

    and traffic loads on bridges”

    Their magnitude and distribution at any given time are uncertain, and even their maximum intensities throughout the life time of the structure are not known with precision.

    Values of live loads are specified in the codes

Densities of Important Materials

Material

Density (Kg/m3)
PCC

2300

RCC

2400

Brick masonry

1900-1930

Earth/Sand/Brick ballast

1600-1800

Intensities of Live Loads

Occupancy / Use

Live Load(Kg/m2)

Residential/House/Class Room

200

Offices

250-425

Library Reading Room

300

Library Stack Room

730

Warehouse/Heavy storage

1200

Basic Design Equation

Max. Service Load = Max. Internal Resistance x F.O.S

Factor of Safety

F.O.S. = Max. Service Load / Max. Failure load

Following points are relevant to F.O.S

It is used to cover uncertainties due to

1. Applied loads

  1. Material strength
  2. Poor workmanship
  3. Unexpected behavior of structure
  4. Fabrication
  1. If F.O.S is provided then at service loads deflection and cracks are within limits.
  2. It covers the natural disasters.

Ultimate Strength Design (USD)/LRFD Method

Strength design method is based on the philosophy of dividing F.O.S. in such a way that Bigger part is applied on loads and smaller part is applied on material strength.

(Applied Load x F.O.S.1< (Material Strength x F.O.S.2)

Ultimate Strength Design (USD)/LRFD Method

(contd…)

Where

< ΦSn

Sn = Nominal Strength

ΦSn = Design Strength

Φ = Strength Reduction Factor

U = Required Strength, calculated by applying load factors

For a member subjected to moment, shear and axial load:

ΦMn ≥ Mu ΦVn ≥ Vu ΦPn ≥ Pu


Allowable Strength Design (ASD)

In allowable strength design the whole F.O.S. is applied on material strength and service loads (un-factored) are taken as it is.

Service Loads < Material Strength / F.O.S

In both Allowable strength design and Ultimate strength

design analysis carried out in elastic range.

fc

Stress

fc‘/2

Concrete

fu

Stress

fy

fy/2

Steel

Strain

Plastic Design

In plastic design, plastic analysis is carried out in order to find the behavior of structure near collapse state. In this type of design material strength is taken from inelastic range. It is observed that whether the failure is sudden or ductile.

Ductile failure is most favorable because it

gives warning before the failure of structures

Objectives of Designer

There are two main objectives

  1. Safety
  2. Economy

Load Combinations (F.O.S1)

To combine various loads in such a way to get a critical situation.

Load Factor = Factor by which a load is to be increased x probability of occurrence

1. 1.4D

2. 1.2D + 1.6L

3. 1.2D + 1.6L + 0.5Lr

4. 1.2D + 1.6Lr + (1.0L or 0.8W)

Where

D = Dead load

L = Live load on intermediate floors Lr = Live load on roof

W = Wind Load


(F.O.S2)

Strength Reduction Factor / Resistance Factor, Φ

Strength Condition Strength Reduction Factor
Tension controlled section (bending or flexure)

0.9

Compression controlled section
Columns with ties

0.65

Column with spirals

0.75

Shear and Torsion

0.75

THANK YOU

learn
We will be happy to hear your thoughts

Leave a reply

Share knowledge
Learn
Logo
Enable registration in settings - general